PPG Paints Water Based Enamel is a premium enamel that has an innovative, grease resistant LTA+ Technology™. LTA+ Technology™ protects the paint surface from hand sweat, grease and household cleaning agents, making it durable and ideal for your doors, windows and trims. PPG Paints Water Based Enamel is also environmentally friendly as it has Low VOC levels and inhibits mould and mildew with an anti-microbial technology. It has a unique non-yellowing formula, making it a good choice for apartments and houses.

Quick guide

Gloss
Ideal for: Interior & exterior doors & trim.
Gloss level: 75-100%
Coverage up to 16 m2 / L - (depending on substrate)
Recoat: 2 hours
Clean up in water

Semi Gloss
Ideal for: Interior & exterior doors & trim.
Gloss level: 45-50%
Coverage up to 16 m2 / L - (depending on substrate)
Recoat: 2 hours
Clean up in water

Low Sheen
Ideal for: Interior doors & trim.
Gloss level: 10-20%
Coverage up to 16 m2 / L - (depending on substrate)
Recoat: 2 hours
Clean up in water

Protect our environment:

Do not pour leftover paint down the drain. Unwanted paint should be brushed out on newspaper, allowed to dry and then disposed of via domestic waste collections. Empty paint containers should be left open in a well-ventilated area to dry out. When dry, recycle steel containers via steel can recycling programs. Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.

Safety & first aid directions

Keep out of reach of children. Keep lid on when not in use.

If swallowed Seek medical advice immediately and show the container or label. Do not induce vomiting.

Eye contact Immediately flush eyes with running water for at least 15 minutes. Seek immediate medical attention.

Skin contact wash skin with soap or recognized skin cleanser. Do not use solvents or thinners. Seek medical advice if irritation occurs.

Call 0800 154 666 for 24 hour medical emergency response service.

PPG Customer Service Call 0800 131 686 toll free or visit www.ppgpaints.co.nz for further information.

Product features

Gloss Level

Gloss

Semi Gloss

Low Sheen

Available in

1L

2L

4L

10L

How to apply

Preparations & Directions:

Surfaces must be clean, dry and free from all surface contamination. Treat mould with bleach then rinse with clean water. Fill in the surface defects with suitable filler, putty or sealant. Avoid using masking tape on wall and ceiling paints.

Previously painted (aged enamel) surfaces

Remove all loose and flaking paint. Sand glossy or enamel surfaces thoroughly and undercoat with PPG Paints 3 in 1 Prep.

Previously painted (other) surfaces

Remove all loose and flaking paint and sand glossy or enamel surfaces thoroughly. Prime bare areas with a suitable PPG preparation product.

To ensure an even surface when painting over patchy or contrasting colours apply a suitable PPG preparation product.

New Work

Paper faced plasterboard, fibre cement, masonry and timber: apply one coat of PPG Paints 3 in 1 Prep.

Application:

Confirm colour before use. Apply two coats using a 4mm – 6mm (length of nap or pile) roller or good quality brush. Avoid overspreading. If painting a large flat trim area, such as a door, apply by roller for best appearance.

• Stir paint in a circular lifting motion for 5 minutes before use
• Drying time: 30 minutes (touch dry)
• Recoat: 2 hours at 25°C (allow 4 hours in cold or humid areas)
• Do not paint at temperatures below 10°C

Coverage:

Up to 16m² per litre. Coverage will be lower on rough or absorbent surfaces.

During Painting:

Ensure adequate ventilation. Keep floors and furniture covered. Keep the lid on containers when not in use.

Clean Up:

Scrape excess paint from equipment into separate container. Wash up with water. Do not dispose of paint or wash water in drains or sewers.

After Painting:

Avoid exposure to steam for 48 hours. Surface may be washed after 7 days but always avoid abrasive cleaners.